God Hand PN-120 single-edged nippers

Product Information

Compared to most nippers, the cut surface is much cleaner and neater, which makes it a good choice for those who want to complete plastic models without painting. Will the God Hands hold up over time? No Idea. They seem to be built very well, they have a built-in stop to prevent them from opening too wide, and another to prevent you from squeezing them to hard, and they included a cover to protect the tips, but sure, they may dull over time and need to be sharpened or replaced. If that happens soon enough to me writing this review to be note worthy, then I will update the review, but for now I am simply amazed. Usually, when I cut pieces out of the sprue, I leave a small nub that I can then cut off with an X-Acto knife. But the God Hand is so sharp and narrow that it can get right up against the part, allowing me to skip the knife step. With the God Hand, my process is this: For people who paint plastic models, this is the best nipper to use because when they cut along the edge, it leaves no remains of the gate. It leaves with a clean cut section. This shortens the time spent on filing the gate. Ultimate Nipper’s superior sharpness comes from its thinly refined cutting edge and single-edge structure for a clean cutting.

The ultimate nipper consists of the cutting blade and the single edged structure which creates super clean cutting surface. Please do not cut plastics that are too long for the blade. The load will be applied to one point, causing it to break or bend. Single Edged Structure is where one blade is the “Cutting Edge” and the other blade is the “Cutting board Edge”, like a knife and a cutting board. Not for photo etched parts Ultra thin single edged! Ultimate Sharpness! . Ultra thin single edged brings excellent performance with less work time! When trying to slice and cut the 3mm runner, the blade will move freely and smoothly without any noise.When cutting out small parts, parts are less likely to fly away, reducing the need to search for missing parts. Poor lubrication of moving parts causes wears on the shaft and rattling, leading to reduced sharpness. Please lubricate the moving parts regularly. Most of the products shown are beingcolored manually, there may be some uneven colorings. Color and form of the product may differ from the actual product and what is seen on screen depending on monitor settings. Some product imagesshown may be in development stage. They may differ from the actual products. All in all, the GodHand SPN-120 is an amazing tool and a must-have for anyone serious about Gundam or models in general. 5 out of 5. Left blade is playing a role to suppress the thing off. Then, sputtering in the blade and cut right.

In case the product, there may be cases, under certain situations, where the delivery date is changed or delayed ,we, VCAGUNDAM.com cannot take responsible for any loss or detriment involved in the use of the service. Please do not twist the blade during cutting or releasing from the runner. Twisting may cause it to break under load. Delivery times are estimates and can vary depending on delivery method selected, time of the year, weather and other factors. If I make sure I’m holding the nippers exactly parallel with the part, I don’t leave an indent or raised angle. If I do it right, I can skip right to filing or sanding.

I will still use my Tamiya snips, after all they do a good job and we always need a set of snips for larger items or resin and the God Hand SPN-120s are intended for plastic only. But if the God Hands hold up then they will become a permanent tool on my bench. If you have a steady hand, and are accustomed to cutting your parts as close to the part as possible (like I do), then these will probably remove most all parts without the need for sanding. The cutting board edge supports an object firmly while the gripping force changes to move the cutting edge smoothly.

The blade is thinner toward the tip and is more likely to break. Please cut as close to the center of the blade as possible. Compared to a standard nipper, the section that is cut has a clean surface which is beneficial to those who want to finish the plastic models without painting. The standard force for cutting 3 mm dia. plastic is 2 kg or less. (General nippers are 3.5 kg to 10 kg) The blade can cut plastics with ease and precision. Please do not grip the nippers with excessive force.To cut off a 3mm plastic, the Ultimate nipper only requires a force of 2kg when a normal nipper requires a force of 3.5-10kg. Cutting Blade and “Single-Edged Structure” striving for clean cutting. If the cutting edge and the cutting board edge are aligned, even the slightest misuse will result in the edges being off. NOTE :หากสั่งสินค้าพร้อมส่งกับสินค้าพรีออเดอร์ในบิลเดียวกันจะรอจัดส่งพร้อมกันเมื่อสินค้าพรีออเดอร์มาครบแล้วนะคะ