Gyproc Plasterboard Patches various sizes 12 Pack (2 x 50mm, 5 x 100mm & 5 x 150mm))

Product Information

Time saving and mess free compared to traditional methods of filing a hole with newspaper and building up layers with filing compound Storage & Home Clearance Furniture Clearance Garden & Outdoor Clearance Lighting Clearance Electrical Clearance Tools Clearance Paint & Decorating Clearance Flooring & Tiling Clearance Building & Hardware Clearance Bathrooms & Plumbing Clearance Kitchens Clearance Once the first coat has set if you find any ridges, lumps, bumps or trowel marks, gently scrape these away using the edge of your filling knife, or leave to fully dry before sanding. Caulk can’t really be sanded down so you need to get it as smooth as possible. For any larger holes you are much better served by a more suitable filler. How Do You Fill Screw Holes In Plasterboard?

Find Gyproc EasiPatch Plasterboard Patches at your local decorator centres and builders’ merchants. Find the details here . Add as much filler as you need to until the hole is filled flush with the surface of the wall. Use the trowel to get the surface as flat as possible.Spread a small blob over the hole and wait for it to dry. Once dry, get a 180-220 grit sandpaper and rub down until smooth and blended with the current surface. How do You Fix a Hole in Plasterboard on the Ceiling? Plasterboard is quite soft and the slightest of impacts such as when moving furniture can mark the surface and even put a hole right through it. The same can also be said for hollow doors – Due to the void in the centre and MDF or fibreboard used as the covering, this does not provide much protection when it comes to resisting impacts. Once the patch is dry and firmly in position, gently remove the screw. Use patching plaster, all purpose filler or multi-finish plaster — mix up enough to cover the patch and gently press into the hole and spread with a putty knife that is larger than the hole to help get a smooth finish. As you will need to do a bit of cutting, before you start this, firstly run over the area around the hole with a wire detector to make sure there aren’t any wires, pipes or other items that you may accidentally cut through.

For larger holes locate the joists either side of the hole in the ceiling and mark the middle with a straight pencil line and create a rectangle around the hole. Cut out and add two noggins to bridge the gap between the joists. When the plaster starts to dry, lightly scratch the surface with the end of the trowel in this pattern.

Wondering how to patch plaster? This is one of those home maintenance jobs that will keep your home looking as fresh as the day it was decorated and patching up plaster just one task you can undertake on a DIY basis Once the Gyproc EasiFill is fully dry, you may see darker patches – this is where the product is chemically set before it air dries. Once painted, these will completely disappear. It’s always good to finish by giving the entire area a light sand for a perfectly, smooth finish.

Holes like these are awkward to fix because there’s often a void behind the board so any filler you put in just disappears. This hole came about when a plumber couldn’t decide where to feed the pipes for a radiator. But fixing holes in plasterboard can be achieved easily… Artex Caulker (250mm ) helps to fill joints and create smooth finishes or any suitable jointing knife Apply the filler by working it into the holes of the patch and towards the edge. Feather out at least 50mm beyond the edges of the patch to create a smooth, seamless finish. Leave to set for a minimum 30 minutes. Now you need to measure and cut two noggins (horizontal wood that bridges the gap between the studs). Use a bit of 2 x 4 inch – approximately 100mm x 50mm – timber to create the noggins. Nail or screw them into position, between the studs, from the sides. This will create an area to fix your new plasterboard patch to.Remove any loose bits from the edge of the hole or damaged area, and sand this down. Remember to always wear eye protection when sanding. To repair a hole in a hollow door, wall, or ceiling, firstly trim the edges of the hole and make is square. Ironically, you actually have to make the hole larger before you can go about fixing it! Another way to fill a hole in plasterboard is to enlarge the hole first to make a square of a suitable size. Then cut two battens (19 x 38mm timber will suffice) and make sure they are 100mm longer than the size of the square you have cut.