Strong Heavy Duty Plastic Kitchen Plinth Clips Kick Board Clips with Attaching Bracket - Pack of 10 - Requires 2 x 3.5mm Diameter Countersunk Screws per Bracket - For Use From Installation Height of 80 mm - Manufactured in UK - Basics UK TM

Product Information

If you don't have many cuts to do, then a hand saw is fine (if you're OK with cutting straight lines). Cut the boards to size with an angle grinder fitted with a diamond disk. Make sure you have a diamond-studded blade or another disk that works on concrete. To use the angle grinder, hold onto it with both hands and move it slowly along the board. Cut across the boards first to trim them to the proper length. Take care of the board’s height afterward, if needed. [7] X Research source You can cut rails out of pine or cedar wood boards. Trim them to the same length as the gravel boards. Place one in the center of the fence, then another along the top. If you’re able to, use a drill bit one size smaller than the screws. It creates small pilot holes that hold the screws more firmly in place. If the holes are too big, the screws won’t stay in. Or bodge it and ‘glue’ them in place with silicone and wind feet down tight onto floor - they ain’t gonna move

Fit the gravel boards into the slots on the posts. Make sure all of the fence panels are out from between the posts. Install the boards by lifting them up and sliding them into the slots on the posts. They can be pretty heavy, so ask a friend to lend a hand. Push them firmly against the ground to ensure they are stable and level. [8] X Research source Concrete gravel boards are easiest to install along metal posts with slots in the side. They can be used with other types of posts, so you don’t have to start from scratch if you already have posts installed. For example, if you have a stretch of ground 48 ft (15 m) long, you could use 8 posts spaced 6 ft (1.8 m) apart. That way, each part of the fence will be equal. You could also space 6 posts 8 ft (2.4 m) apart. Use a bubble level to make sure the boards are even. Test the boards one by one. Set the level on top of one of the boards, then watch the liquid capsule in its middle. It has a bubble that will shift to one side, depending on which one is higher. Make adjustments to each board until they are all level. [9] X Research sourceThe boards are available online and at many hardware stores. They can also be bought from fencing companies. Use a masonry drill bit to make 7 mm (0.28 in) holes in the posts. Plan on making the pilot holes roughly the same size as the screws you’re using. Fit the bit on a power drill, then carefully drill through the spots you marked. Make each hole about 7 mm (0.28 in) deep, or about the same length as the screws you’re going to use. [15] X Research source I use a suction device used for lifting glass. You can get these quite cheaply from Screwfix. 2020-06-02T16:05:02+01:00 Plant the fence posts if they haven’t already been installed. Measure the perimeter of your yard, or wherever you plan on installing fencing. Space the fence posts 6 to 8 ft (1.8 to 2.4 m) apart. As a rule of thumb, dig holes that are about ⅓ the height of the posts to provide plenty of stability for your fence. Then, secure the posts by filling the holes in with cement. [1] X Research source Fine teeth in the saw for sure, and I'd use tape across the cutline while cutting to make sure the edge is as clean as possible.

Either screw up into base of cabinet using a short stubby screwdriver or a right angled drill attachment Also I read to use aquaseal - this is supposed to stop water getting under, and also helps stop water getting inside the chip board. Does this sound right? We have tiles that go under the kicthen cabinets. Instead of shortening the gravel boards, use shorter panels on your fence. You could also cut existing fence panels shorter to ensure your fence is at the height you desire. Put on safety glasses and a dust mask before cutting gravel boards. Plan on working outdoors, if possible, to prevent any concrete dust from getting into your home. If you’re working indoors, open nearby doors and windows to let out the dust, or use any ventilation fans you have installed. Avoid wearing a long-sleeved shirt, jewelry, or anything else that could get caught by the blade. [6] X Research source

If you do not feel confident in being a DIY-er, or would prefer to not use your time on a project like this, get in touch with a professional to make your life easy and complete the job in a timely and skilful way. Superdrug adds new 'VIP Rewards' offers to its existing loyalty scheme – here's what you need to know