DIATOOL 3 Inch/75MM Vacuum Brazed Diamond Grinding Wheel Half-Round Edge Edge Profile for Stone Abrasive Grinding disc Vacuum brazed Profile Hand Diamond Wheel Grit 60 （Diamond Height 20mm）

Product Information

EFFICIENT & POWERFUL: The Edge Diamond Grinding Wheel is more wear-resistant than ordinary edge grinding wheels. It is simple, safe, and easy to use, and the high-quality coarse diamond surface ensures excellent performance on multiple surfaces. Xxx DH, Xu Z (2019) Dressing methods of superabrasive grinding wheels: A review. J Manuf Process 45:46–69 Schröer N (2018) Spannutschleifen von Hartmetall-Schaftwerkzeugen mit gradierten Schleifscheiben. Dr.-Ing. Dissertation, Technische Universität Berlin The RUBI PRO-EDGER range of diamond grinding wheels are for exclusive use with the RUBI PRO-EDGER accessory for grinders.

Edge chipping of silicon wafers in diamond grinding (PDF) Edge chipping of silicon wafers in diamond grinding

Uhlmann E, Hübert C (2011) Tool grinding of end mill cutting tools made from high performance ceramics and cemented carbides. CIRP Ann Manuf Technol 60(1):359–362 Mayr J, Barbist R (2014) Untersuchung und Bewertung der Schleifbarkeit von Hartmetall. Der Stahlformenbauer 31(4):74–79 Due to smaller grain sizes in the area of the grinding wheel edge, the cutting edge roughness could be reduced. Jin T, Stephenson DJ (2006) Heat flux distributions and convective heat transfer in deep grinding. Int J Mach Tools Manuf 46(14):1862–1868

Hussain Bux & Co.

Egashira K, Hosono S, Takemoto S, Masao Y (2011) Fabrication and cutting performance of cemented tungsten carbide micro-cutting tools. Precis Eng 35:547–553 RUBI PRO-EDGER diamond grinding wheels are especially recommended for beveling and mitering porcelain sheet pieces with the highest efficiency and the highest quality in the final results.

Edge Diamond Grinding Wheel, 3 inch Profile Hand Diamond Edge Diamond Grinding Wheel, 3 inch Profile Hand Diamond

Grain concentration and grain size directly influence the occurring wear during deep grinding. The results show that there is a maximum (percolation threshold) in grain concentration due to structural bonding failure. In particular, the thermal load often defines the process limits in flute grinding and can thus be associated with the strong increase in wear in the area of a high depth of cut [ 16]. A purely experimental approach can iteratively lower the wear in these areas by increasing the grain concentration, as shown in the results of the ungraded grinding wheels, too. Apart from this, it also shows that a reduction of the wear difference is possible by adjusting the area-related number of grains to the local related material removal rate according to formula 4. Zhang FH, Kang GW, Yang YS et al (2006) EDM dressing for metal-bond super hard arc-forming wheel. In: Key Engineering Materials. Trans Tech Publ, pp 99–103 Ohmori H, Kasai T (1997) Development of metal-resin bonded diamond wheel for ELID-lap grinding and its grinding performance. In: ICPE `97, Taipei, Taiwan: 177–181 Kuai J, Zhang H (2019) Research on generation and polishing mechanisms of nano grain α-Fe2O3 in precision electrolytic in process dressing (ELID) grinding. Proc Manufact 37:425–430Ceramic tile or stone finishes, whether natural or sintered, are the culmination and most visible part of any cladding job. RUBI PRO-EDGER diamond grinding wheels offer excellent results on any ceramic tile format. Lu YJ, Li LJ, Xie J, et al (2017) Dry electrical discharge dressing and truing of diamond grinding wheel V-tip for micro-grinding. In: 2017 5th International conference on mechatronics, materials, chemistry and computer engineering (ICMMCCE 2017). Atlantis Press, pp 548–552 Bifano TG, Dow TA, Scattergood RO (1991) Ductile-Regime grinding. A new technology for machining brittle materials. J Eng Ind. 113(2):184–189